| | | | | | | |  | Opa Helmut ashtray with toffeePP Solid Pipe and Fittings | | | | | | | | | | | Description (available only in german language) size: 145 x 50 x 185 mm1.We are manufacturing PP Solid Pipes and Fittings which are being widely used for handling corrosive chemicals and organic compounds and also for ultra pure water, and waste anddrainage water lines under the moderate pressure.Solid pipe is suitable for operating pressure up to 3kg/cm2 without outside housing forthe temperature range of -18°C ~ 107°C. Their prices are cheaper than steel pipe, CPVC or other chemical resistant plastic pipes.PP solid pipe is light weight materials with specific gravity of 0.90~0.91, so easy to handlefor transport, fabrication and installation. 2. Property of Polypropylene CopolymerThe polymer resin for manufacturing PP solid pipe and fittings has the following properties: Properties Typical Data Test Method Density 0.90 ~ 0.91 g/cm3 STM D1505 Tensile Strength at Yield 280kg/cm2 STM D638 Elongation at Break <500% STM D638 3. PP Solid Pipe SpecificationsOur standard specifications of PP solid pipe are as shown on the table below non-standard pipes will be available the customer's specific requirements. Nominal Pipe Size Pipe O.D. Pipe Thickness Pipe I.D. 15 21 2.5 16 20 25 3.0 19 25 32 3.0 26 40 48 4.0 40 50 58 4.5 49 65 74 6.0 62 80 88 6.0 76 100 113 7.0 99 125 138 7.5 123 150 161 8.0 145 200 213 9.0 195 250 265 9.5 246 300 304 10.0 284 400 390 10.0 370 4. PP Pipe Fittings Standard pipe fittings are 90°C Elbow, 45°C Elbow, Tee, Reducing Tee, Concentric Reducer, Eccentric Reducer, Socket, Lateral, Cross. Coupling, Floor Drain, Flange for sizes from 15 mm up to 300 mm. Flange dimensions will conform to ANSI or KS standards. 5. Installation 1) Loading, off-loading and transport of PP pipes and fittings shall be carried out carefully so as to avoid any sudden impact on pipes and fittings. 2) Fabrication of PP Pipes and Fittings should be made by PP welding machine with PP welding rod. Before welding, the connection areas of pipes and fittings shall be cleaned with alcohol or dry and clean cloth. 3) All fittings are socket connection type and pipe should be fully inserted into the sockets of fittings before welding. PP welding should be carried out with welding rod slowly so as to integrate pipe and socket into one body by the fusion. 4) PP flanges along with Teflon gasket shall be used to connect with tank's nozzles or flanged type valve. Flange bolts shall be tightened carefully to avoid any damages like bending, cracking to PP flanges by over-torquing. Threaded type valve shall be connected with PP valve socket. 5) When PP pipe and fittings are installed overhead, the piping shall be fixed tightly to pipe supports or hangers. 6) When the pipe assemblies leak during hydrostatic test after welding, the welding areas in leakage shall be repaired following the methods 2) and 3) stated above. 7) Fire or any fire work shall be avoided close to PP pipe and fittings. |
| | [ Contact Info ] |  Company | ARG Global Co., Ltd.1.We are manufacturing PP Solid Pipes and Fittings which are being widely used for handling corrosive chemicals and organic compounds and also for ultra pure water, and waste anddrainage water lines under the moderate pressure.Solid pipe is suitable for operating pressure up to 3kg/cm2 without outside housing forthe temperature range of -18°C ~ 107°C. Their prices are cheaper than steel pipe, CPVC or other chemical resistant plastic pipes.PP solid pipe is light weight materials with specific gravity of 0.90~0.91, so easy to handlefor transport, fabrication and installation. 2. Property of Polypropylene CopolymerThe polymer resin for manufacturing PP solid pipe and fittings has the following properties: Properties Typical Data Test Method Density 0.90 ~ 0.91 g/cm3 STM D1505 Tensile Strength at Yield 280kg/cm2 STM D638 Elongation at Break <500% STM D638 3. PP Solid Pipe SpecificationsOur standard specifications of PP solid pipe are as shown on the table below non-standard pipes will be available the customer's specific requirements. Nominal Pipe Size Pipe O.D. Pipe Thickness Pipe I.D. 15 21 2.5 16 20 25 3.0 19 25 32 3.0 26 40 48 4.0 40 50 58 4.5 49 65 74 6.0 62 80 88 6.0 76 100 113 7.0 99 125 138 7.5 123 150 161 8.0 145 200 213 9.0 195 250 265 9.5 246 300 304 10.0 284 400 390 10.0 370 4. PP Pipe Fittings Standard pipe fittings are 90°C Elbow, 45°C Elbow, Tee, Reducing Tee, Concentric Reducer, Eccentric Reducer, Socket, Lateral, Cross. Coupling, Floor Drain, Flange for sizes from 15 mm up to 300 mm. Flange dimensions will conform to ANSI or KS standards. 5. Installation 1) Loading, off-loading and transport of PP pipes and fittings shall be carried out carefully so as to avoid any sudden impact on pipes and fittings. 2) Fabrication of PP Pipes and Fittings should be made by PP welding machine with PP welding rod. Before welding, the connection areas of pipes and fittings shall be cleaned with alcohol or dry and clean cloth. 3) All fittings are socket connection type and pipe should be fully inserted into the sockets of fittings before welding. PP welding should be carried out with welding rod slowly so as to integrate pipe and socket into one body by the fusion. 4) PP flanges along with Teflon gasket shall be used to connect with tank's nozzles or flanged type valve. Flange bolts shall be tightened carefully to avoid any damages like bending, cracking to PP flanges by over-torquing. Threaded type valve shall be connected with PP valve socket. 5) When PP pipe and fittings are installed overhead, the piping shall be fixed tightly to pipe supports or hangers. 6) When the pipe assemblies leak during hydrostatic test after welding, the welding areas in leakage shall be repaired following the methods 2) and 3) stated above. 7) Fire or any fire work shall be avoided close to PP pipe and fittings. | | Address | ducki-dong 416 Goyang-City Ilsan-Gu Gyeonggi-do 411-800 Korea | | Phone | 82 - 31 - 9233092 | | Fax | 82 - 31 - 9233093 | | Homepage | www.withherb.com | | Contact | |
| | | | | | | |
| | | | |